BILBO TOOLBAGINS

Finally, he's getting to that tool bag post he's talked about...

Here it is. I finally decided to pull out my tool bags and take some pictures.
I have many tools, most located in my tool chest/drawers. However, I keep some of my tools in tool bags, ready to grab and go when and if the call is made. This all started with my time with Brethren Disaster Ministries, and has spiraled out of control.

The bags. I keep the Tool Box in my car, as it is my on the go auto repair box.

It all started with my tool belt, so we will start there.

I headed down to Lorida with just tool belt containing a hammer, and a cast paw. I picked up some tools down there, and added a pouch when I came back.

The belt will be replaced eventually, but it really suits me now.

The Hammer and Claw: Eastwing 16oz and Cast Paw

A general purpose hammer with a smooth face. I swung this hammer almost nonstop for 5 days from sun up to sun down. Never really fatigued me. The cats (cast) paw is invaluable for ripping nails out.

Tool Belt Accessories: Knife, Punch, Screw, and Tape

I added these when I picked up the pouch. It contains a basic screw driver with changeable bits, your standard Stanely 99e knife with extra blades (including roofing blades), finishing punches, and a tape measure I was given when I was down there.

Multipurpose Pliers: Linemans 369

Just a multipurpose pair of Lineman's pliers. I use them to pull nails and staples, snip wire and cords, and hold nails to hammer when I hit my thumb.

The Tool Bag: Cave of Wonders

This is where it starts to spiral out of control. I started buying these things as needed, for around the house, but always kept in mind the need for travel should I need too.

This guy is packed

The Power Tools: Milwaukee M12 Sawzall, Hammer Drill, Impact Driver, and Flashlight

Started with just the Impact driver and went on from there. I'm really impressed with the M12 line. the smaller sized tools are great for travel, and the power is just as good as the bigger M18's we use at work. The only reason I can see using the larger M18 would be for a portable 1/2 inch drive impact gun. The impact driver is a beast, and I have used it a ton.

Milwaukee Accessories

Just bits and pieces for the drill and driver. Those multi-step bits are the bomb. The drill bits dont do so well in the impact driver. Once the impact part kicks in, they chatter to much and stop drilling.

The Other Guys: Estwing 28 oz waffle, Ball Peen, and Wonder Bar, as well as a Nail Pouch, Files, and Air Shim.

The 28 ounce hammer has yet to be used, but was bought with the intention of framing and driving larger nails. The Ball Peen is for smaller trim work, as well as shaping and flattening tin when making roof patches. The wonder bar is for making those old shingles fly. Also used for shimming and adjusting. I picked up the nail pouch down in Lorida, and it was worn in conjunction with the basic tool belt.

The bar file is for reshaping the cast paw and hammer claws, as well as knocking down nail heads and other pokey bits of metal. The Rat Tail file has yet to find a purpose, but enlarging holes is probably what will happen. The Air Shim is awesome. Its a little air bladder that you can use to shim, adjust, and lift things. Comes in real handy when putting shelves on Ikea furniture.

Other Things: Wiss Aviation Shears and Torpedo Level

The first thing I bought when I got back from Lorida was the shears. We were installing metal roofing, and they would have really come in handy. I used some down there to make brackets out of scrap metal to rehang gutters as well as cut the metal roof pieces. The Torpedo level is just a level. I bought one with a magnet and pipe grove for setting fence posts. It also comes in handy with Ikea furniture.

Not pictured is my Ryobi laser level cube. I forgot to take a pic, but it's just a laser level. I use it for marking studs. Also not pictured is my Studdy Buddy. Its a hand held magnet that you use to locate studs in the wall.

Tape Measures

The Fat Max is and awesome tape measure, and the other is my cheater tape. It has the fractions written out on it.

THE SAW BAG: It's a bag with a circular saw in it.

Milwaukee M12 Circular Saw

All this bag has in it is the saw. It's a smaller saw, using a 5 3/8 inch blade, but it will cut a 2x4 in one pass. Very torquey, and the battery life is pretty decent with one of the larger M12 batteries.

The Plumbing Bag

There isn't too much in here. I am just starting to build it. I also use some of my work tools if I am around the house.

Slim Pickings: Just a pliers and a wrench

As of right now, this is it. A 14" Pipe Wrench and a set of Channel Locks. Again, when I am around the house, I use some of my work tools. I'll be ordering some offsets and speed wrenches here soon, as well as some other plumbing related things.

Well, there you have it. My tool bags. I hope to put them all in use soon, as the trip with BDM to Lorida was truly an amazing time. I would do it again in a heart beat.

I am going to make my tool box a separate post as it's not home related, more auto. It' will come soon enough.


Ok, enough is enough. This was a large post, and I am tired of typing.

Mudhole: Eternal

Ok, I slacked off a bit this week...

Off my game last week as:

1. We had Monday off
2. I've been with out a truck most of the week (DEF crap)
3. Had to take off Friday because the youngest one decided to be sick.

Anyways, we did have a leak or two, and an exceptionally muddy one on Thursday.

Main side, lateral leak. Domestic.

What started as a small leak, turned into a giant mud hole. Normally, when you have two services (meters) next to each other, the end up tying in together at a "Tee". Then that tee feeds into the main. If you go back on some of the posts I have had about leaks, you can see this.

Well, we expected this as well with this leak, but... this was not the case.

Strike First. Strike Hard. No Mercy

It turned soupy, quick.

When digging down on an active leak, it can get a little hard to see what you are doing. Most initial guesses as to what is broken is done with the hands, and not the eyes. This is why we were confused when it felt like a 3/4 inch line was feeding from the main. Normal, as mentioned above, there would be a tee. Tee's are always going to be a larger diameter that the lines that feed off of them (what we call the service). So it made no sense to have a 3/4 line feeding off the main, splitting into two 3/4 services. That would cause a volume issue for the two customers on that lateral line, should they both try to use water at the same time.

ANYWAYS.

We dug on.

Trying to keep the water off us long enough to figure out what is going on.

Is the lateral over here?

Or is it over here

The hole got wetter, deeper and wider as we went. Eventually we uncovered the right service and verified that it was indeed a single service tied directly into the main, with no tee. This would mean the other service would be the same.

The single tap off the main

The service was broke right at the main. She let go once we started missing with it.

After a new service was built and screwed into the main, we could stop the water flow, and build back. I always take this time to look at what broke, and why.

This weird metal/pvc female adapter broke. Over tightened more than likely on install.

Rebuilding each service in poly. 

Ground was still muddy as could be.

Very muddy. A few boots were lost

Made sure the lines were flushed, and and backfilled what we could.

Still wet!

What. A. Mess.

Then on to the most important part of the day. Lunch.

Well, that all for now.

I go oncall this next week, from Monday to Monday. It's my first time as an on call leader, so I'm sure that will be fun and bring it's own challenges. (I hate being oncall by the way.)

Here's to the next time!

Mud Holes, Forever

The week seemed to be dry and all the clothes were too clean.

But we got a chance to get a little dirty before the week was through. 

A few leaks popped up this week, some where passed off to other crews, but we fixed a few ourselves. Friday was the muddy one.

A reuse leak came in a few days before, but it was small so we let it go for a couple days.  Since it was reuse water, we shut (we thought) the main off so it could dry up (it didnt).

We headed out Friday morning to get it fixed. I hooked up to a trailer and we brought out our BobCat and a mud pump.

No matter where you go, make sure your hair is fabulous.

A few scoops taken out for exploratory reasons.

The main ended up not being off all the way, and the somebody turned the main back on with someone else in the hole. Main was shut off all the way, then the repair began. Ended up being a slipped fitting coming off the main tap saddle.

Mud hog pumping down the hole

Squeeeeezing the bucket between the main and other utilities.

I thought the main was off!?

After we got down to the break, I headed back to the yard with a trailer full of mud. That proved to be a task. All that muck settled driving back to the yard, and suction cupped itself to the trailer floor. I had to hand shovel it all out.

Brownies?

The mud did not move. At all. I even shook the tar out of the trailer and nearly broke the hitch.

After getting more dirty emptying the trailer than I did working, I loaded up some fresh dry dirt to back fill the hole, and headed back. Fuel first.

All the lights

Once back, both reuse services were built back in poly. Meter boxes were set, and we began to backfill. All in all the repair went the way it should.

Tee'd straight off the main.

Not much leak action this week, but I'm sure there will be more next week. I think we have a repair scheduled to remove a meter from a driveway, so that should be fun.

See you later!

Captian's Log: 3

This weekend was a little laid back, not too much to report. Spent some time with family on Friday, and worked on the car a little as well.

This Saturday's project was the beginning of the conversion of MK6 Golf parts onto my MK5 Rabbit. Long story short, my Rabbit came with 150hp/170lbft and a 5500 RPM redline. The late MK5s and MK6 Golfs came with 170hp/177lbft and a 6300 Redline. I will be getting the Rabbit tuned for a 6500 Redline, and in prep for that, I am switching over to all the MK6 parts I can.

First step was the exhaust manifold. The MK5 is an open chamber type manifold. There are hardly any runners at all, and its mostly just an empty chamber full of turbulence. The MK6 manifold is slightly less open, with actual runners. It does open up at the end, but is more "header-like" and almost a true 5-1 manifold. I could have bought an actual header, but they stopped making the good ones years ago, and if you find them online, they are usually $1000 dollars. I would never dream of spending that on a full cat back, much less a header. You can get ebay knock offs, but they are prone to cracking, and I would have to cut up my stock exhaust to make it fit.

MK5 on the left, MK6 on the right. Port holes are the same diameter, MK5 is just dirty.

Swap was pretty straight forward. After removing a few pieces and sensors, everything came up and over the engine with no fuss. About half the studs came out with the manifold nuts, but after a trip to the touch, and using jam nuts, they came right off. The studs were then cleaned and soaked in PBlaster, and all new brass nuts, as well as new OE MLS gaskets were used.

Do not pass go, go directly to torch.



Everything was buttoned up, and then the Rabbit was fired up.

 

Word for the wise, PBlaster smokes like a son of a gun.

 

ProTip: Unbolt the exhaust hanger and the down pipe slides right on.

 I don't have a heat shield yet (one is on the way), so I made do with some reflective heat material, and overlapped it on my fire wall. I'll leave it for added protection once the heat shield gets here.

REVIEW

 

Over all impressions are good! Sound has noticeably changed. Idle sounds more "uneven" (like how I think a 5 cylinder should sound), and under wide open throttle, it is louder. There is almost a trumpet-like blast. Seriously, I picture a chunky kid blasting the hardest note through a trumpet or trombone when I hear it.

 

Power is obviously unchanged for now, but again, this is just a supporting mod for the tune.

 

 

So if you hear something on the Westside that sounds like hells angels blasting trumpets, it's probably me in my pokey VW Rabbit.

 

 

 

More later!